Vermont-castings TP-250 Manuel d'utilisateur télécharger pdf

20012371 11/07 Rev. 3

Fuel Conversion Kit

Installation Instructions

Kits:

Natural to LP:

20011992, 20012367, 20012368

LP to Natural:

20013200, 20013199, 20013196

for Models: DVT38IN,

DVT44IN, DVT38S2IN

This kit is designed for conversion of the Direct Vent

Gas Heater Models DVT38, DVT44 and DVT38S2

equipped with the American Flame AF-4000 Series

valve.

Tools required for conversion: TORX T20 Security Tee

bit, 3/8” and 1/2” deep well socket, Phillips or Robertson

screwdriver, 5/32” allen wrench, small ﬂat blade screw-

driver, 7/16” nut driver or socket.

Check Contents of Shipping Carton

Compare contents of Figure 1 with actual parts re-

ceived. If any parts are missing or damaged, contact

your dealer before starting conversion.

Conversion Precautions

Allow unit to cool if it has been operating.

Before proceeding with conversion shut off ﬁreplace

and turn gas supply OFF. Turn OFF any electricity that

may be going to appliance.

Conversion Procedure

1. Remove glass frame. Refer to Homeowner’s Manual.

2. Remove lava rock, volcanic rock, embers and logs.

Carefully remove brick panels.

CAUTION: Logs may be hot.

3. Models DVT38, DVT44

a. With a Phillips or Robertson screwdriver, remove

the two (2) screws holding the fettle to the burner

assemblies. With a hex, remove the two (2) hex

nuts holding the burner tube to the front of the

burner assembly. Remove burner tube.

b. With the 3/8” socket remove two (2) hex nuts

holding the left burner leg. Remove burner leg.

(Fig. 2)

FP1559a

remove nuts

3/05

Hex Nuts

FP1559a

Fig. 2 Use 3/8” socket to remove hex nuts holding left burner

leg.

c. Slide the burner housing assembly to the left and

away. Adjust air shutter setting. Pull burner tube

assembly forward and out. Adjust air shutter set-

ting. Refer to Table 2.

d. Remove two (2) screws holding the pilot as-

sembly to the burner assembly. Move the pilot

assembly toward the back.

e. Slide the burner housing assembly to the left and

away.

f. With the 1/2” socket, replace the three (3) injec-

tors. Refer to Table 1.

3. Model DVT38S2

a. With a Phillips or Robertson screwdriver, remove

the four (4) nuts holding the fettle to the burner

assemblies. With a hex, remove the two (2) hex

nuts holding each burner tube to the front of the

WARNING!

The installation of this conversion kit must

only be undertaken by a qualiﬁed, certiﬁed

gas appliance installer.

CAR205

DVTIN

fuel conversion

5/07 djt

Burner Oriﬁce (3 or 4)

(Refer to Table 1 or 3

to Conﬁrm Sizes)

CAR205

Fig. 1 Carton contents.

Pilot Oriﬁce

Label

Valve Minimum

Rate Screw

(DVT44,DVT38S2)

Pressure

Test Adapter

Valve Minimum

Rate Screw

(LP) (DVT38)

1 2 3 4

Résumé du contenu

Page 1 - Fuel Conversion Kit

120012371 11/07 Rev. 3Fuel Conversion KitInstallation InstructionsKits: Natural to LP: 20011992, 20012367, 20012368LP to Natural:20013200, 20013199,

Page 2 - 

22CO134AF pilot orifice3/07Index TabSnap RingAllen WrenchCO134Fig. 5 Remove pilot oriﬁce.CO133pilot hood3/07Pilot BracketPilot HoodCO133Fig. 4 Remov

Page 3 - 

319. Using a 7/16” nut driver, remove the threaded plug from the test port.20. Thread the supplied extension adaptor into the open test port.21. At

Page 4 - CFM Corporation

44© CFM CorporationTable 3 DVT38S2 Injector Oriﬁce Size Matrix Conversion to LP KiT # Burner 20012368 Burner Housing/ Burner Burner

Commentaires sur ces manuels

Pas de commentaire

Vermont-castings TP-250 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Grilles Vermont-castings TP-250. Vermont Castings TP-250 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Grilles Vermont-castings TP-250